Have more questions? Contact us!
The Magnuson-Moss Warranty Act makes it illegal for companies to void your warranty or deny coverage under the warranty simply because you used an aftermarket part. READ MORE…
Download PDF here… FPOR0255
Your Billy Boat Exhaust system was designed to be a direct replacement exhaust system while offering the best performance, finish and value available from a stainless steel exhaust system. Proper installation will ensure a lifetime of quality and performance from this product.
1) Disconnect the NEG (-) battery terminal.
2) Remove the factory exhaust system by removing one side at a time.
3) Loosen the small clamp that connects the Cat converter to the muffler.
4) Remove the large muffler clamp. Rotate and lift the existing muffler off of the mounting bracket and lower out of the vehicle. Save the existing small clamp and exhaust donut. They will be reused during the install.
5) Loosen the tip clamp. Remove Tip. Save the tip clamp and donut. They will be reused during the install.
6) Use the same procedure for the other side.
7) Install the Billy Boat Exhaust system by placing the muffler tab onto the muffler bracket. Align the muffler tube with the Cat converter exit reusing the existing exhaust donut and clamp and hand tighten. Slip the large supplied muffler clamp over muffler and align on muffler bracket and hand tighten. Align as needed and tighten clamps. Align supplied tip reusing the existing tip clamp and donut.
8) Repeat the procedure for the other side muffler.
9) Reconnect the battery NEG (-) terminal.
10) Start vehicle and check for exhaust leaks.
SAFETY: Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the installation.
VEHICLE SUPPORT WARNING: Should the purchaser decide to install this exhaust product at home, be warned that car or light duty truck/van “bumper” jacks are intended for emergency use only. The use of frame contact jack stands in conjunction with a floor jack as main support is highly recommended to minimize accidental dropping of a vehicle while the installation proceeds. We recommend the use of a shop hoist if possible. Please use caution!
GENERAL STATEMENT OF LIABILITY: While we provide information for do-it-yourself installation of exhaust systems and related items, these operations are not without risk. Injury may occur during an installation or exhaust systems and their components may be damaged in the process. We are not responsible or liable for damages that may be sustained to persons or property during an installation. For this reason, we recommend professional installation as the best option when at all possible. While care has been taken in the preparation of the information contained in this web site, Billy Boat Exhaust and BillyBoatExhaust.com does not and cannot guarantee its accuracy. Anyone accessing this information does so at their own risk. It will be assumed that access indemnifies Billy Boat Exhaust and BillyBoatExhaust.com from any and all injury or damage arising from such use.
LOCAL LAWS & LIMITATION OF LIABILITY/DISCLAIMERS: Local Laws & Limitation of Liability/Disclaimers: The regulation of emissions production, noise levels and safety standards is undertaken by the federal government, each of the fifty state legislatures, and by many local municipalities, towns and counties. The manufacturer makes no warranties of merchantability, of fitness for a particular purpose, or that its products are approved for general use, or that its products comply with laws, regulations or ordinances in the states where they may be sold to the ultimate purchaser, the consumer. The entire risk as to the conformity of this product in any such state and as to repair, should the product prove to be defective or non-conforming, is on the retail purchaser, the buyer, the ultimate consumer of such product and it is not upon the seller, distributor, or manufacturer. In this connection, retail purchaser, the buyer, the ultimate consumer assumes the burden of the entire cost of any and all necessary service, alterations, and or repair. The foregoing statement limits the liability of the manufacturer.
If you have any questions please feel free to give us a call. Our direct line to the sales departments is 1-888-228-7435, ext 18. We are in Phoenix, AZ and can be reached 8am-5pm. Should you have questions that images would help explain, please email Mike at email@example.com.
*Please note, we do not follow daylight savings time if you are contacting us outside of Arizona.
We try to put as much information as possible within our product pages to help with application choice and the installation process. The business you purchased our product from can be a wealth of information, but should you need additional help and information, please feel free to call or our sales department.
Monday-Friday 8:30am-5:00pm Arizona time.
888-228-7435 x18 or 623-581-7600 x18
*Note that Arizona does not follow Daylight Savings Time.
More information in additional browser tab.