(888) 228-7435
Menu

Nissan 350Z Cat Back Exhaust System (Round Tips) #FPIM-0075

Product Details

Nissan 350Z Cat Back Exhaust System (Round Tips) #FPIM-0075
  • 4 1/2″ Twin ROUND Rolled-Edge Tips.
  • Mandrel bent from the highest-grade T-304 stainless steel.
  • Designed, tested, and manufactured to the finest hand-made integrity found in any exhaust system.
  • Limited Lifetime Warranty

 

Have more questions? Contact us!

The Magnuson-Moss Warranty Act makes it illegal for companies to void your warranty or deny coverage under the warranty simply because you used an aftermarket part. READ MORE…

 WARNING: This product in the physical form it is sold does not present a hazard. However, operations including, but not limited to welding, brazing, or thermal cutting can expose you to chemicals including Chromium, Nickel, Cobalt, Arsenic, Cadmium and Lead which are known to the State Of California to cause cancer, birth defects and other reproductive harm. For more information go to www.P65Warnings.ca.gov
STOCK BBE         STOCK BBE  
RPM HP HP  GAIN     RPM TORQUE TORQUE  GAIN
1500 51 52 1 1500 179 182 3
1600 55 57 2 1600 182 186 4
1700 59 61 2 1700 184 188 4
1800 64 66 2 1800 186 191 5
1900 69 70 1 1900 191 193 2
2000 74 76 2 2000 196 199 3
2100 81 83 2 2100 203 207 4
2200 86 88 2 2200 205 211 6
2300 90 93 3 2300 205 212 7
2400 95 98 3 2400 209 214 5
2500 99 102 3 2500 209 214 5
2600 103 105 2 2600 210 212 2
2700 108 109 1 2700 210 211 1
2800 113 113 0 2800 212 212 0
2900 118 119 1 2900 213 214 1
3000 122 124 2 3000 214 216 2
3100 127 129 2 3100 215 218 3
3200 131 133 2 3200 215 218 3
3300 135 137 2 3300 215 218 3
3400 139 142 3 3400 215 219 4
3500 143 146 3 3500 215 220 5
3600 148 151 3 3600 216 220 4
3700 153 156 3 3700 217 221 4
3800 157 162 5 3800 218 223 5
3900 162 165 3 3900 219 222 3
4000 166 170 4 4000 218 222 4
4100 172 174 2 4100 220 223 3
4200 176 180 4 4200 220 225 5
4300 181 185 4 4300 221 226 5
4400 186 190 4 4400 222 227 5
4500 192 194 2 4500 224 227 3
4600 194 200 6 4600 222 229 7
4700 199 205 6 4700 223 229 6
4800 205 210 5 4800 224 230 6
4900 208 214 6 4900 223 229 6
5000 209 214 5 5000 220 225 5
5100 207 216 9 5100 213 223 10
5200 209 218 9 5200 211 220 9
5300 212 218 6 5300 210 216 6
5400 216 222 6 5400 210 216 6
5500 218 227 9 5500 208 216 8
5600 222 229 7 5600 208 215 7
5700 223 230 7 5700 206 212 6
5800 225 231 6 5800 204 210 6
5900 225 231 6 5900 200 206 6
6000 224 232 8 6000 196 203 7
6100 228 234 6 6100 196 202 6
6200 229 236 7 6200 194 200 6
6300 228 233 5 6300 190 195 5
6400 226 231 5 6400 186 190 4
6500 225 229 4 6500 181 185 4
6600 224 228 4 6600 178 181 3

 

How a Dyno Works

We’re going to quote DynoJet directly to explain how the machine works, since paraphrasing would only do you an injustice. “Power, in mechanical terms, is the ability to accomplish a specified amount of work in a given amount of time. By definition, one horsepower is equal to applying a 550-pound force through a distance of one foot in one second. In everyday terms, it would take one HP to raise a 550-pound weight up one foot in one second. So to measure horsepower, we need to know force (in pounds) and velocity (in feet per second). DynoJet’s inertia dynamometer measures power just in this way. The dyno calculates velocity by measuring the time it takes to rotate the heavy steel drum one turn. The dyno measures force at the surface of the drum by indirectly measuring the drum’s acceleration. Acceleration is simply the difference in velocity at the surface of the drum from one revolution to the next. The force applied to the drum is calculated from acceleration using Newton’s 2nd law, F=MA, (F)orce equals (M)ass times (A)cceleration. Power is coupled to the drum by friction developed between the driving tire of the vehicle and the knurled steel surface on the drum of the dynamometer.”

Calculating Torque

“When an object rotates around a point, the object’s speed of rotation depends on both an applied force and the moment arm. The moment arm is the distance from the point of rotation to where the force is being applied. Torque is the product of the force and the moment arm. For example think about trying to spin a drum by wrapping a rope around the drum and then pulling on the rope. If the rope is wrapped around a drum of one-foot radius and pulled with 550 pounds of force, the resulting torque is 550 foot-pounds. The torque on the dyno’s drum can be calculated by multiplying the force applied by the drum’s radius. However, engine torque is not equal to the dyno’s drum torque because the gearing through the drivetrain changes the moment arm. The change in the moment arm is proportional to the ratio of engine speed to drum speed. Therefore, tachometer readings are necessary to calculate and display engine torque.”

 

Download PDF here… FPIM0075

Layout1

Your Billy Boat Exhaust system was designed to be a direct replacement exhaust system, while offering the best performance, finish and value available from a stainless steel exhaust system. Proper installation will ensure a lifetime of quality and performance from this product.

 

1) Disconnect the NEG (-) battery terminal. Disconnecting power from your vehicle may allow the computer to “clear” its memory during installation.

2) With the engine cool, remove the factory exhaust system, starting from the first connection after the catalytic converter, and working back.

3) Be sure to inspect all rubber hangers before installation and replace as necessary.

4) Starting at the catalytic converter, install the front pipe using the supplied gasket. Install the middle pipe using the supplied clamp. Only finger tighten the supplied hardware at this time.

5) Install the muffler section by aligning the inlet pipe on the muffler with the middle pipe. Slip the muffler onto the existing rubber hangers. Only finger tighten the supplied hardware at this time.

6) With the Billy Boat Exhaust system “hanging loose,” begin tightening all hardware starting from the front of the vehicle and working your way back.

7) Reconnect the battery NEG (-) terminal.

8) Start vehicle.

9) With the vehicle running at an idle, check for exhaust leaks at each connection. If there is a leak, check that the mounting hardware is tight.

10) Enjoy this fine product for the life of your vehicle!


Billy Boat Exhaust Safety, Installation and Liability Statements

SAFETY: Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the installation.

  • Always wear safety glasses for eye protection.
  • Place the ignition switch in the OFF position.
  • Always apply the parking brake when working on the vehicle.
  • Block the front and rear tire surfaces to prevent unexpected vehicle movement.
  • Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide.
  • Do not smoke or use flammable items near or around the fuel system.
  • Use chemicals and cleaners only in well-ventilated areas.
  • Batteries can produce explosive hydrogen gas which can cause personal injury. Do not allow flames, sparks or flammable sources to come near the battery.
  • Keep hands and any other objects away from the radiator fan blades.
  • Keep yourself and your clothing away from moving parts when the engine is running.
  • Do not wear loose clothing or jewelry that can be caught in rotating or moving parts.

VEHICLE SUPPORT WARNING: Should the purchaser decide to install this exhaust product at home, be warned that car or light duty truck/van “bumper” jacks are intended for emergency use only. The use of frame contact jack stands in conjunction with a floor jack as main support is highly recommended to minimize accidental dropping of a vehicle while the installation proceeds. We recommend the use of a shop hoist if possible. Please use caution!

GENERAL STATEMENT OF LIABILITY: While we provide information for do-it-yourself installation of exhaust systems and related items, these operations are not without risk. Injury may occur during an installation or exhaust systems and their components may be damaged in the process. We are not responsible or liable for damages that may be sustained to persons or property during an installation. For this reason, we recommend professional installation as the best option when at all possible. While care has been taken in the preparation of the information contained in this web site, Billy Boat Exhaust and BillyBoatExhaust.com does not and cannot guarantee its accuracy. Anyone accessing this information does so at their own risk. It will be assumed that access indemnifies Billy Boat Exhaust and BillyBoatExhaust.com from any and all injury or damage arising from such use.

LOCAL LAWS & LIMITATION OF LIABILITY/DISCLAIMERS: Local Laws & Limitation of Liability/Disclaimers: The regulation of emissions production, noise levels and safety standards is undertaken by the federal government, each of the fifty state legislatures, and by many local municipalities, towns and counties. The manufacturer makes no warranties of merchantability, of fitness for a particular purpose, or that its products are approved for general use, or that its products comply with laws, regulations or ordinances in the states where they may be sold to the ultimate purchaser, the consumer. The entire risk as to the conformity of this product in any such state and as to repair, should the product prove to be defective or non-conforming, is on the retail purchaser, the buyer, the ultimate consumer of such product and it is not upon the seller, distributor, or manufacturer. In this connection, retail purchaser, the buyer, the ultimate consumer assumes the burden of the entire cost of any and all necessary service, alterations, and or repair. The foregoing statement limits the liability of the manufacturer.

If you have any questions please feel free to give us a call. Our direct line to the sales departments is 1-888-228-7435, ext 18. We are in Phoenix, AZ and can be reached 8am-5pm. Should you have questions that images would help explain, please email Mike at mike@bbexhaust.com.

*Please note, we do not follow daylight savings time if you are contacting us outside of Arizona.

We try to put as much information as possible within our product pages to help with application choice and the installation process. The business you purchased our product from can be a wealth of information, but should you need additional help and information, please feel free to call or our sales department.

Monday-Friday 8:30am-5:00pm Arizona time.
888-228-7435 x18 or 623-581-7600 x18

*Note that Arizona does not follow Daylight Savings Time.

More information in additional browser tab.

Newsletter Sign Up