Billy Boat Exhaust manufactures hand-fabricated x-pipes in both 2 1/2″ and 3″ to help the LS! and LS1 C6 engine breath. These x-pipes will smooth out the exhaust pulses of your engine and give you a cleaner exhaust note and additional horsepower. These are also available with catalytic converters if you have headers and also resonators to help tune the exhaust sound level.
Have more questions? Contact us!
The Magnuson-Moss Warranty Act makes it illegal for companies to void your warranty or deny coverage under the warranty simply because you used an aftermarket part. READ MORE…
Download PDF here… FCOR0435
With proper installation your new Billy Boat Exhaust system will last a lifetime. While installation of this product is very simple and straight forward, there are a couple areas that need some attention.
#1- Secure vehicle to wheel lift.
#2- With the car safely lifted and chocked remove the nuts and bolts that hold the roll bar and lower the anti-roll bar from the center chassis mounts. It is not necessary to completely remove the bar; it just needs to be moved in order to get the axle hoops out. (Note: if just replacing the center section, the anti-roll bar will not have to be moved.)
#3- Unbolt the flanges located at the front of the factory center pipe. Then remove the nuts that are holding the spring hangers at the rear of the center pipes. Loosen clamps on rear of center pipe. Pull center pipe back off the donuts at the front of the exhaust system. Lower center pipe down and pull forward off the front of the mufflers and set aside.
#4- To remove the mufflers, pull the hangers through the rubber mounts and lower the mufflers down and unwrap from over the axle. You may have to move the mufflers to one side or the other to get them out.
#5- Position the new muffler/axle hoop system into place. Then insert the mounting hook into the factory rubber hanger. Mate the muffler/axle hoop system to the center pipe (Billy Boat X-Pipe if used) in the reverse order of removal and just tighten them enough to still allow for movement while aligning the system. *But do not tighten them completely. (Note: if using the Bill Boat prt center muffler make sure that the gussets are pointed up towards the bottom of the car. Prt center pipes can be rotated to adjust height of center muffler.)
#6- With all components in place, use a straight edge along the bottom of the tips for proper alignment. Keeping in mind that it will take some time to align them correctly.
#7- Then start by tightening the flanges in front of the system first and then the nuts, bolts and clamps connecting the muffler sections making sure everything is still in alignment.
#8- Fire the car up and take it for a spin around the block making sure there are no rattles.
#9- After logging on a few hundred miles re-torque your work.
Tools need for installation:
Jack/Jack Stands, 17mm & 18mm Socket or Wrench, 15mm Socket and Wrench, 13mm Socket and Extension
SAFETY: Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the installation.
VEHICLE SUPPORT WARNING: Should the purchaser decide to install this exhaust product at home, be warned that car or light duty truck/van “bumper” jacks are intended for emergency use only. The use of frame contact jack stands in conjunction with a floor jack as main support is highly recommended to minimize accidental dropping of a vehicle while the installation proceeds. We recommend the use of a shop hoist if possible. Please use caution!
GENERAL STATEMENT OF LIABILITY: While we provide information for do-it-yourself installation of exhaust systems and related items, these operations are not without risk. Injury may occur during an installation or exhaust systems and their components may be damaged in the process. We are not responsible or liable for damages that may be sustained to persons or property during an installation. For this reason, we recommend professional installation as the best option when at all possible. While care has been taken in the preparation of the information contained in this web site, Billy Boat Exhaust and BillyBoatExhaust.com does not and cannot guarantee its accuracy. Anyone accessing this information does so at their own risk. It will be assumed that access indemnifies Billy Boat Exhaust and BillyBoatExhaust.com from any and all injury or damage arising from such use.
LOCAL LAWS & LIMITATION OF LIABILITY/DISCLAIMERS: Local Laws & Limitation of Liability/Disclaimers: The regulation of emissions production, noise levels and safety standards is undertaken by the federal government, each of the fifty state legislatures, and by many local municipalities, towns and counties. The manufacturer makes no warranties of merchantability, of fitness for a particular purpose, or that its products are approved for general use, or that its products comply with laws, regulations or ordinances in the states where they may be sold to the ultimate purchaser, the consumer. The entire risk as to the conformity of this product in any such state and as to repair, should the product prove to be defective or non-conforming, is on the retail purchaser, the buyer, the ultimate consumer of such product and it is not upon the seller, distributor, or manufacturer. In this connection, retail purchaser, the buyer, the ultimate consumer assumes the burden of the entire cost of any and all necessary service, alterations, and or repair. The foregoing statement limits the liability of the manufacturer.
If you have any questions please feel free to give us a call. Our direct line to the sales departments is 1-888-228-7435, ext 18. We are in Phoenix, AZ and can be reached 8am-5pm. Should you have questions that images would help explain, please email Mike at email@example.com.
*Please note, we do not follow daylight savings time if you are contacting us outside of Arizona.
We try to put as much information as possible within our product pages to help with application choice and the installation process. The business you purchased our product from can be a wealth of information, but should you need additional help and information, please feel free to call or our sales department.
Monday-Friday 8:30am-5:00pm Arizona time.
888-228-7435 x18 or 623-581-7600 x18
*Note that Arizona does not follow Daylight Savings Time.
More information in additional browser tab.